Basically, Horton has slashed prices so most of its stock of cut nails are $6 a pound, with the exception of the expensive cut headless brads, which are $6 for 1/4 lb. (still a good price).
I’m a tool chest guy. At the end of the day all my tools go back in my chest to protect them and to soothe my head (I am a tidy German). When I’m working with my tools at the bench, I also like to keep them sorted – simply so I can work faster.
And that’s why I bought a Texas Heritage Woodworks Saddlebag and screwed it to the rear of my workbench. (FYI, I buy all my tools and etc. at full retail. I receive no “promotional consideration,” “affiliate monies” or “reach-arounds.”)
Like everything Jason and Sarah make, the quality is top notch. The seams are tidy, sturdy and riveted for strength. The pockets are thoughtfully designed to hold a variety of small woodworking tools.
My Saddlebag is set up to work like a traditional rack on a French workbench – it’s located opposite the face vise and slightly below the bench’s work surface. With the Saddlebag in this spot I can stick my typical small tools there while I work, and I always know where my 6” square and mechanical pencil are. (My ears are simply too big to tuck a pencil there – it would have to be the size of one of those pencils we had in kindergarten.)
The Saddlebag is also ideal for hanging inside a Dutch tool chest (check out this gallery of these chests on the Popular Woodworking blog).
I’m sure this will be on my “Anarchist’s Gift Guide” this holiday, so now you can beat the rush.
Big slabs of wood move as they dry – sometimes a little, sometimes a lot. In my experience, the worst of the movement happens in the first six to 12 months of drying. The hardest two problems to deal with that emerge from the drying process are: a crown over the length of the slab, and the more common twist or wind over the length.
This movement (particularly a bad twist) can mean removing a tremendous amount of wood to get a flat surface. A jack plane with a cambered iron can do wonders, but if there is a lot of wood that has to come of it, can be quite a job. Another factor can be the wood itself. Most of the benchtops I deal with are red or white oak; once dry, it is hard to take much of a bite with a handplane.
The past couple of years I have been using a hand held electric plane for hogging off the majority of the offending wood. It works quite well across or with the grain. When using it cross-grain it will take close to 1/8″ off each pass. Once I am close to where I need to be, I can easily finish up with handplanes.
These little electric planes vary in price, I think I paid $120 for the one I have. This one has seen some pretty heavy use and has held up well so far.
This top had about 1/2″ of twist over 6′ length. It took about 10 minuets to get it true enough to move on to a surface planer or handplane.
In the video Chris and I shot, “Roubo Workbench: by Hand & Power,” we used one of these electric planes to flatten one face of the benchtop. We did the opposite face of the top with a 20″ surface planer. After all was said and done, wrestling the 300 lb. benchtop through the surface planer was much more exhausting than going the electric plane/handplane route.
The following is a description of the break room at the military museum where I worked as a carpenter’s assistant in 1987.
Part of the farewell card I made for my colleagues when I left.
By far the best thing about the job was the break room, where about a dozen of us from different departments gathered each morning around half-past 10, then for lunch at one, and again, later on, for tea. An industrial-size kettle sat on the stove; a roster indicated who would be in charge of making tea before the others arrived. On my first day, George told me how much tea to throw in the pot and how high to pour the water when the kettle boiled. There was always a bottle of milk in the fridge and a bowl of sugar nearby.
The men would stroll in, pour themselves a cup of tea, and take their customary places. Aside from two younger fellows, most of them appeared to be in their 50s or 60s and coasting toward retirement. The break room sped them on their way like one of those moving sidewalks at the airport.
Most of them were married. Their wives packed their lunches, wrapping sandwiches in neat paper or plastic bags, tucking in a packet of crisps alongside some radishes or carrots from the garden. They’d pop in some other little treat — a couple of chocolate digestives, a small container of fruit cocktail, a slice of leftover Madeira cake from a picnic with the grandkids. It seemed clear that most of these men were well cared for and well trained. And because they were expected to behave themselves at home, they leapt at the chance to have some fun with the 27-year-old temp.–Excerpted from Making Things Work
The “Sharpen This” stickers have been making the rounds on Instagram – this is my favorite one so far.
My daughter Maddy reports she still has a fair number of this set of stickers left. So if you want a set, here are the details. You can order a set of three from her etsy store here. A set is $6 delivered ($10 for international orders).
Or, for customers in the United States, you can send a $5 bill and a SASE (self-addressed stamped envelope) to by daughter Maddy at:
Stick it to the Man
P.O. Box 3284
Columbus, OH 43210
As always, this is not a money-making venture for me or Lost Art Press. All profits help Maddy through college. (She’s a senior!)
