Author: Lost Art Press
Publisher of woodworking books and videos specializing in hand tool techniques.
The Sound of this Photograph
OK now, before we get started here I want you all to gather around there behind the bench. Like a family photo. We are going to gang-cut all the dovetails on all your tail boards with this one saw from Lie-Nielsen.
Yup. One cut. One and done. And you are going to be amazed.
Yup. Look amazed. Chris, drop your left hand there so we can see the saw in all its awesomeness.
Now remember folks this is amazing. Look amazed. Ready?
‘The Packing Box’ for One Book
The first project that young Thomas builds in “The Joiner and Cabinet Maker,” is a packing box, which was meant for a customer who was taking some books to the countryside.
Most modern-day readers skip building the packing box and move right on to the second project in the book, the schoolbox. And that’s too bad, because the packing box is great fun and has some good lessons in working entirely by hand.
One reader came up with a great use for a packing box. I love it. The box mimics the box on the cover and in the book. Great idea.
— Christopher Schwarz
Wounds in the Workshop, Minor and Otherwise
I’m not afraid to pull down my pants, turn my head and cough when it comes to discussing workshop practice. And after reading this very interesting bit on treating wounds with French polish, I decided to discuss some of the stuff I do – advisable or not.
When I cut myself in the shop and it’s not ER-able, the first thing I do is wash out the wound in the sink with running water and soap. Then I put some Neosporin or some such on the wound.
But how do I close the wound so that I can continue to work? That depends.
If it’s real minor, I use fabric bandages from the drugstore. Yawn, I know. But these bandages – no matter how much money I spend on them – are usually wrecked when I move my joints. Most woodworking wounds are on the hands, so most bandages don’t last long.
So if it’s a bleeder, I take some other steps that have worked well in my shop for 15 years without any problems. First, clean the wound. Clean it. Clean. It. Then:
1. Blue tape and a clean paper towel. Yup, make your own custom dressing with these two common shop products. Why do I do this? It’s a much more “adaptable” dressing. Even good fabric bandages don’t last the whole day in the shop. Blue tape sure does. And the tape resists dirt. Fabric bandages absorb it.
2. Cyanoacrylate with accelerator. This is my favorite wound-closer. After cleaning things out, I’ll press the wound together, apply some cyano over it and squirt it with accelerator. If it’s a wound on a joint, I’ll usually add a second coat of cyano to make a tough skin. I follow that up with the blue tape/paper towel as noted above to keep the dirt out, and I am good to go.
3. Recently, I’ve made some bandages from clean strips of cotton (old T-shirts) soaked with hide glue. You make the bandages beforehand so they look like light brown strips of dried bacon. But they work. You wrap them around the wound and they tack pretty quick. I still prefer cyano over all the other methods, but this is a good field solution.
I know that the doctors will likely cringe at my methods. But I have had far fewer problems with infection once I started actively closing the wounds with cyano and blue tape.
— Christopher Schwarz
If They’d Had a Biscuit Joiner…
… then they would have had joints that failed suddenly instead of slowly and gradually – like a mortise-and-tenon does. I know this after dropping an anvil on a lot of joints.
If they’d had a router, they would have used it – unless they didn’t want to sand out all the machine marks on the mouldings.
If they’d had a dovetail jig, they would have used it – unless they didn’t want the jig to dictate the height of their drawers.
If they’d had a random-orbit sander, they would have used it – unless they were skilled with a handplane, which would make them faster than the sander. And they might not wanted to spend the money on sandpaper, which has always been expensive.
If they’d had PVA, they would have used it – unless they wanted their joints to be reversible and unless they wanted to dial in the gram strength and open time of their adhesive.
If they’d had dowels, they would have used them – unless they preferred a joint that wasn’t mostly end grain.
If they’d had a table saw, they would have used it – unless they wanted zero grain runout on their stock (which is what you get when you rive your wood) so it was as strong as possible.
If they’d had a drill press they would have used it – unless they wanted to drill a hole at any other angle than 90°.
If they’d had a chop saw they would have used it – unless they wanted to saw something angled or compound.
OK, I’m sure you’re sick of this line of thought. I am. Truth is, I dislike talking about this sort of stuff. Work wood the way you want to. But when you get assaulted by people who say that power tools would rule if they were sent back in time through some wormhole, I have to laugh.
I have access to a CNC machine. I would never use it for building furniture.
I have access to fancy word processors that will correct my grammar, spelling and punctuation, but I never use them. They slow me down, try to correct things I don’t want to correct and generally get in the way of good writing.
I could buy a car with an automatic transmission, but it would interfere with the amount of control I want when I drive.
I prefer vinyl over digital music. Et cetera.
We all make choices about the technology we employ in every task we do. So why would we assume that the people of the past would like to do things the way we do? I sure as heck don’t want to “print” a piece of furniture using a 3D printer. Trust me, that’s coming.
When that day arrives, then maybe all woodworkers will stand united. Until then, let’s allow the woodworkers of the past rest in peace.
— Christopher Schwarz
P.S. Be sure to read Peter Follansbee’s take on this topic on his blog.