Make Your Own Curved Card Scraper


Note: Our Crucible card scrapers sold out in just a few hours. We’re in the process of making hundreds and hundreds more and hope to have them up for sale in a couple weeks.

If you didn’t get a chance to purchase one of the Crucible curved card scrapers, you can make your own with a dry grinder and an existing card scraper. It takes about 30 minutes.

Download and print out the following template. It’s a hand-drawn version of Chris Williams’s scraper, which is where our design started.


Cut it out and affix it to your card scraper with the help of spray adhesive. Or make a cardboard template and trace its shape on your scraper with a permanent marker.

At your grinder, set the tool rest to 0° – parallel to the floor. Dress the wheel of your grinder (we use an #80-grit wheel, but a #60 or #100 will also do) so it has a slight convex shape. This convexity in the wheel makes the scraper easier to shape.

Get a bucket of water and put it by the grinder.

(Hey wait, where are the step photos? I’m in a hotel room that’s 400 miles from my shop. You are going to have to use your imagination.)

Place the scraper on the tool rest and start grinding the excess metal away. Don’t work on one part of the scraper for more than a few seconds. Keep moving around the perimeter. After 10 or 15 seconds, try to pinch the scraper with a finger and thumb. If….

… you can pinch the scraper with no pain, continue to grind.

… your fingers reflexively jump away, cool the scraper in your water bucket.

… you smell bacon, also cool the scraper in the water bucket.

Once you have ground down to your line, you will have become pretty good at grinding flat shapes – congrats. Now you need to remove the grinder marks from the edges.

Use a block of wood to hold the scraper at 90° on a coarse diamond stone and stone the edges. Remove all the scratches from the grinder. Then move up to a #1,000-grit waterstone (or soft Arkansas) and then up to a polishing stone. Then you can proceed with normal scraper-sharpening procedures.

This is exactly how I made all of our prototypes. I promise that you will become emotionally involved with your scraper after putting all the work into it, and you might not ever want to buy one of ours.

So be it.

— Christopher Schwarz

About Lost Art Press

Publisher of woodworking books and videos specializing in hand tool techniques.
This entry was posted in Crucible Tool, Uncategorized. Bookmark the permalink.

45 Responses to Make Your Own Curved Card Scraper

  1. jpassacantando says:

    I’m loving that Schwarz puts his card scraper for sale (I bought one) and then puts out instructions on how to make your own. He is an anarchist through to his core. Reminds me that he should steal the essence of the title of Abbie Hoffman’s book someday, “Steal This Book.”

    • Bob Easton says:

      Exactly as Christopher promised a while ago. He’s a man of his word.
      I have a scrap of saw blade set aside, and I was also fortunate enough to buy one early in the day.

      THANKS Christopher.

  2. snwoodwork says:

    Can you put the outline of the magnet up as well?

  3. Tracy Wright says:

    i made some of these a few months ago when you first posted the pattern. i made a template out of 1/4″ plywood and shellacked it. great scraper. when i get some money i’m going to buy one of yours as well as a thank you.

  4. And here I thought the statement, “you could make your own” was instruction enough. Now with the promise of Bacon, how can we resist?

  5. Now I’m forced to ask what an “Ulm” Logo is

  6. Jay Froman Sr. says:

    So, I didn’t get in to order in time. Is there a wait list for the next batch? If so put my name on it please?

  7. Al says:

    Is it possible to make these from an old saw?

    • Bob Easton says:

      Don’t know how Christopher would answer this, but I’ve had very good success using remains of a vintage Disston that some previous owner had manged to kink.

      Avoid the “bacon” step and be painstakingly scrupulous in stoning a nice square edge, and you’ll be very happy with the result. Then again, if your labor is worth more than $20…

    • Yup. Cutting down the plate to a scraper-sized chunk is usually the biggest obstacle. I’ve used a nibbler, but it’s not a common tool in most woodshops.

      • Al says:

        Cool. Cutting it down is the easy part for me. Takes about 45 seconds on a stomp shear. Ive never used a scraper so ive been hesitant to buy one. Almost got one of yours but I hesitated. I knew I shouldn’t have. I just don’t have any woodworking projects at the moment, so just didn’t need it right now.

      • Gav says:

        If gentle a zip disc on an angle grinder works a treat. They don’t generate a lot of heat and I have found with repurposed saws I can trim all the old teeth off and start afresh with no loss of temper if careful. Bit quicker than grinding the whole line flat. The dremel cutting discs can work well too.

      • Scott Maurer says:

        I can’t vouch for it’s effectiveness in steel long term but I found a nibbler drill chuck attachment a couple years ago. It works great on brass but I’ve not gone at it in steel to find out if it can get through a saw plate.

  8. mark fisher says:

    Advice on material thickness?

  9. ant11sam says:

    “You smell bacon…” LOL LOL

  10. Dave says:

    I made mine the day you posted about it in 2018. The shape made sense to me. I have not picked up any of my 6-7 other scrapers since. And I used to think those rectangles were the best tool in the shop.

  11. Donald Kreher says:

    I have always first cut my card scrapers (from TGIG) to approximate shape with tin snips. Then ground to final shape using sometimes a ceramic belt on the belt sander. This stays much cooler.

  12. Pablo says:

    Downloaded template expand it to b larger!


  13. Mitch Wilson says:

    One of the guys I took classes with at Connecticut Valley School of Woodworking took a course with Phil Lowe, about 6 or so years ago. He taught them about this style of card scraper and I, in due course, made one as well. It certainly is a big improvement over the plain rectangular ones.
    And, as Mark Adams taught us at WIA/2010, you can sharpen the short sides of the scrapers as well. Just be careful where you put your fingertips when in use.

  14. Derek Cohen says:

    Chris, I am curious about the thickness of your scraper. I do not recall reading anywhere what this was, and assumed it was standard fare (as per a saw blade – 0.02″).

    For some years I have been posting about the scraper I use a lot of the time. I made this from the rear half of a 3/16″ O1 parallel plane blade. It has a flat side and a curved side. It sharpens simply by hollow grinding (I use a 180 grit CBN wheel). No burr, etc. Stewmac make something similar. However I credit the idea to Philip Marcou (planemaker), who once mentioned to me that he had done this with D2 steel (or similar).

    The reason I ask about the thickness of your scraper is that one of the aims of yours is that it does not have to be bent with the thumbs. The curved shape permits this. A thicker blade would also do so, and the hollow-ground-created-burr is so fast to do. One might expect that the result is a coarse finish, but it leaves a smooth surface in its wake.

    Regards from Perth


    • Our scraper is .032″ thick. I’ve used that StewMac one – one of the other editors had one back in the lat 1990s or early 2000s, if I recall. Effective but heavy.

  15. Tex ritter says:

    I have one that is similar in shape, but I have never used it. No idea where I got it, but it is labelled ” E Garlick & Son”. Same thickness of .032″, and I probably never used because I am used to flexing the scraper, and thick ones are too tough to flex easily. Now I am encouraged to try it out.

    It’s cruder than the Crucible tool version, with the small edges sheared off straight, with no radius on the corners. What seems like a nice feature is that the two ling edges have a different radius to them.

Comments are closed.